Basic-Six Method for Tuning Native American Flutes
This page describes a basic method for tuning six-hole Native American flutes in the
pentatonic minor scale. It is assumed that the flute has a cylindrical sound chamber bore, as opposed to a bore that is tapered or has pertubations. This tuning method is designed to bring only the notes in the primary scale of the instrument as well as one cross-fingered note into tune.
For a version of this method designed for five-hole flutes, see the Basic-Five Method for Tuning Native American Flutes. For a more ambitious tuning method that brings all the cross-fingered notes into tune, see the Bob Grealish Method for Tuning Native American Flutes.
This tuning method is simplified version of the tuning method contributed to Flutopedia by Robert Grealish, as described in a document originally
posted on the
Native Flute Woodworking Yahoo newsgroup on July 23, 2007 and updated on August 5, 2014.
The goal of the Basic-Six tuning method is to bring seven fingerings into tune with seven specific notes. Six of those notes, shown in black, play the
pentatonic minor scale.
And one additional note, shown in red, is very useful for flute players and adds substantial diversity to the melodies that can be played:
Figures 1 below shows the notes we will be tuning for a mid-range, six-hole, F# Mode 1/4 Native American flute. Solid circles represent closed finger holes and open circles represent open finger holes.
Figure 1: Scale for an F# minor pentatonic,
six-hole Native American style flute.
If you need a chart for a key of flute other than the F# minor flute shown here, the Basic Native American Flute Design Tool can be useful. Simply set the Fundamental Note and click Calculate. If you want to add the cross-fingered notes, check the “include cross-fingerings” box.
Terms, Concepts, and Definitions
For reference, here are the parts of the flute mentioned on this page:
External and internal elements of a Native American flute
Also, this page also uses Flute Maker Numbering for the holes — playing hole 1 is the hole nearest the foot end of the flute. This is a common convention among flute makers since this is the finger holes that is tuned first:
Numbering the holes on a Native American flute
When tuning a flute, you start by tuning the note with all finger holes closed. After that note is tuned, you generally proceed by opening holes at the South end and proceed up the flute,
tuning each finger hole and the holes below it open. Each finger hole starts out small, and its note is flatter than the target pitch for that note. You make a note sharper to bring it into tune by enlarging the hole opening.
Let’s assume you are making an F#, pentatonic minor flute. First, tune the fundamental note of the flute () by cutting the foot end back or by placing and enlarging direction or tuning holes. Next, using the Flute Sheet Excel spreadsheet, NAFlutomat, or another method described on the Finger Hole Placement page, calculate where your playing holes will be. Start by designing them all close to the same diameter and then adjust the hole diameters until the finger spacing is reasonably even.
Mark the locations of the finger holes on the flute. Hereafter I will assume you are burning the holes, but if I say to burn a hole, you could just as well grind or file the holes instead of burning. Start with hole 1 and move up. Start each hole small and tune it up before starting on the next hole. Tune it by gradually enlarging it while checking the tuning of the note.
Gradually make hole 1 larger until it comes in tune with A. After hole 1 is tuned, check the tuning for the fundamental note () to see if it is still in tune.
Enlarge hole 2 to bring it in tune with a B. After hole 2 is tuned, check the tuning for hole 1 () to see if it is still in tune with A.
Enlarge hole 3 to bring it in tune with a C#.
After hole 3 is tuned, re-check the tunings for hole 2, hole 1, and the fundametal note (). At this point, you may start to see some “drift” in notes you have tuned earlier. This can happen, because making a finger hole larger increases the volume inside the sound chamber slightly. This affects the tuning of the notes below it. Fortunately, the effect is to make the previously tuned notes slightly flat, so you can simply make the corresponding finger holes slightly larger.
Hole 4 is the one note that is outside of the pentatonic minor scale. However, tuning it is not different than the other notes. Simply close holes 3, 5, and 6 and gradually make hole 4 larger until it comes into tune.
Gradually make hole 5 larger to bring it in tune with an E.
Hole 6 is the octave note, F#, one octave above the fundamental. Gradually make hole 6 larger to bring it in tune with an F#.
At this point, you should again check for drift in the notes you have tuned earlier. It is likely that at least some of the notes you tuned earlier will need a slight adjustment.